+libcec (2.0.1-1) unstable; urgency=low
+
+ * changed/added:
+ * added Loewe support
+ * added signal handlers to client applications
+ * Documentation updated
+ * replaced cec-config-gui by libCEC tray
+ * log the exact data for failed transmissions, not the opcode
+ * don't log every frame, unless debugging was enabled in ./configure or
+ visual studio
+ * changed some log levels from NOTICE to DEBUG, so the non-debugging output
+ is less spammy
+ * interface changes:
+ * WARNING: breaking API changes
+ * clean up: deprecated methods and fields removed
+ * callback parameters changed to fix plain C compilation
+ * added GetAdapterProductId()+GetAdapterVendorId()/
+ cec_get_adapter_product_id()+cec_get_adapter_vendor_id()
+ * added iDoubleTapTimeoutMs to libcec_configuration
+ * remove all pre-v2.0 compatibility checks
+ * fixed:
+ * fix plain C compilation
+ * prevent sending directly addressed commands from being sent to broadcast
+ * don't wait for a response when sending a reply, so we don't block message
+ handling
+ * message response signaling and logging
+ * prevent double taps by not sending the same key press twice within 200ms
+ * fall back to the primary client when
+ CCECProcessor::HandleLogicalAddressLost() and no client could be found
+ * no more delay up to 2 seconds when exiting libCEC
+ * don't get caught in a loop in CVLCommandHandler when the source switch
+ was not allowed and no power status request was sent
+ * always send image view on to the tv, don't check the power status
+ * only respond to vendor commands for panasonic if we are the destination
+ * rpi: current firmware first sends a change to logical address 'broadcast'
+ and then signals us that the address was lost. libCEC then failed to
+ re-register, because it didn't know any client at this address
+
+ -- Pulse-Eight Packaging <packaging@pulse-eight.com> Mon, 8 Oct 2012 21:30:00 +0100
+
+libcec (1.9.1-1) unstable; urgency=low
+
+ * changed/added:
+ * added the type of adapter to libcec_configuration,
+ and display the type in cec-client -l
+ * added device detection support for composite usb devices on windows.
+ needs the windows ddk, and it's expected to be found in
+ C:\WinDDK\7600.16385.1
+
+ * interface changes:
+ * adapter type was added to libcec_configuration
+ * moved cec_adapter_messagecode from cectypes.h to USBCECAdapterMessage.h
+
+ * fixed:
+ * retry m_port->Read(..) if an EINTR errror occurs instead of closing the
+ connection. credits @Obruni. closes #38
+ * make cec-client include cecloader.h from our project, not from system
+ * fixed duplicate entries check in CUSBCECAdapterDetection
+ * fixed missing cec_version updates in libcec_configuration
+ * transmit an active source message after <set stream path> to a device
+ that's handled by libCEC. closes #43
+ * rpi: handle vendor specific remote control presses. closes #42
+ * rpi: handle VC_CEC_LOGICAL_ADDR_LOST, sent by the Pi's firmware when
+ the logical address was taken while CEC was being reinitialised
+ * panasonic: send out an active source message when the tv started up
+ because it sometimes doesn't request this
+
+ -- Pulse-Eight Packaging <packaging@pulse-eight.com> Wed, 5 Sep 2012 16:54:00 +0100
+
+libcec (1.8.2-1) unstable; urgency=low
+
+ * changed/added:
+ * p8: match to the response provided by the firmware when checking
+ responses (added in firmware v2 rev6)
+
+ * fixed:
+ * windows: update the error message when an error occurs while writing to
+ the serial port
+ * delayed source switch time was reset, resulting in an attempt every
+ second until it succeeded
+ * ensure that the vendor commands are always sent for panasonic, and that
+ the deck status for lg isn't reset. fixes some buttons not working after
+ a second or delayed source switch
+ * added guard so ReplaceHandler() doesn't accidently try to replace a
+ handler for the broadcast address
+ * wait until the commandhandler is replaced before registering a client,
+ so we don't register a client and replace it directly afterwards if the
+ tv doesn't support the device type
+ * ensure that the command handler of the tv is replaced before registering
+ a client, or it might result in a double eeprom write attempt
+ * p8: don't disable controlled mode when switching to monitoring mode
+ * p8: do delayed eeprom writes async or it'll block processing other input
+
+ -- Pulse-Eight Packaging <packaging@pulse-eight.com> Tue, 3 Aug 2012 02:35:00 +0100
+
+libcec (1.8.1-1) unstable; urgency=low
+
+ * changed/added:
+ * added support for the Raspberry Pi.
+ * added cec-client -i / cec-client --info that calls GetLibInfo()
+ * header cleanups
+ * added CAdapterFactory, to create IAdapterCommunication instances
+ * added --debug to configure, to include -ggdb
+
+ * interface changes:
+ * added GetLibInfo()/cec_get_lib_info(), that shows how libCEC was compiled
+ and with which features included.
+ * added ToString(cec_user_control_code_key) to the interface
+
+ * fixed:
+ * disallow sending CEC_OPCODE_SET_STREAM_PATH - not allowed by the CEC spec
+ * persist the configuration in the eeprom after initialising the client.
+ fixes wrong/old settings being used in autonomous mode, which broke the
+ wake on cec funtion
+ * persist the new configuration when the hdmi port setting changed
+ * cleaned locks around callbacks
+ * always set controlled mode to false when unregistering the last client.
+ fixes 30 second timeout before controlled mode gets deactivated
+ * updated the cached device type setting properly when persisting new
+ settings. correct return value from WriteEEPROM(). lock a mutex when
+ updating the state
+ * LibCecSharp: set the primary LA in CecLogicalAddresses
+
+ -- Pulse-Eight Packaging <packaging@pulse-eight.com> Tue, 25 Jul 2012 13:05:00 +0100
+
libcec (1.7.2-1) unstable; urgency=low
* changed/added:
repositories / deb_libcec.git / blobdiff