+libcec (2.0.3-1) unstable; urgency=low
+
+ * changed:
+ * log unhandled vendor remote keycodes in the log, so they get logged
+ without debugging enabled
+ * double tap timeout increased from 200ms to 250ms
+ * CuBox/NXP* renamed to TDA995x*
+ * fixed:
+ * handling of active route changes. github issue #56 and issue #58
+ * new combo key handling broke samsung's vendor specific remote buttons.
+ github issue #54
+ * don't try to set controlled mode when using firmware version 1 and crash.
+ github issue #76
+ * fix for LG models that send a vendor key up after a normal key down.
+ github issue #71
+ * some TVs send keypresses to us without making us the active source. mark
+ us as active source when this happens. github issue #71
+ * LG doesn't send routing changes, and marks the TV as active source when
+ switching to another source that's not been selected in the simplink menu
+ instead. this change keeps libCEC marked as powered on and keep the deck
+ state set to CEC_DECK_INFO_OTHER_STATUS_LG. fixes keypresses not working
+ after switching to another source and back to libCEC's hdmi port via the
+ source select menu instead of the simplink menu. github issue #71
+ * don't respond with an abort message when receiving a vendor remote button
+ command
+ * respond with CEC_ABORT_REASON_INVALID_OPERAND when receiving a keypress
+ without a parameter
+ * typo in stop+pause combo key that prevented one of the keys from working
+ * rpi: log what data we received exactly when we receive an response from
+ the pi's firmware that doesn't match any command that we sent. issue #77
+ * cubox: added adapter ID interface
+
+ -- Pulse-Eight Packaging <packaging@pulse-eight.com> Wed, 31 Oct 2012 15:57:00 +0100
+
+libcec (2.0.2-2) unstable; urgency=medium
+
+ * fixed:
+ * updating the device status after a poll was broken and could reset the
+ status of devices that were marked as handled by libCEC to 'not
+ present'
+ * don't keep spamming the bus with a vendor command when an active source
+ switch is pending for panasonic, but only send it when needed
+ * reset CVLCommandHandler::m_bCapabilitiesSent when the TV goes to standby
+
+ -- Pulse-Eight Packaging <packaging@pulse-eight.com> Mon, 15 Oct 2012 13:52:00 +0100
+
+libcec (2.0.2-1) unstable; urgency=low
+
+ * changed/added:
+ * missing from the previous changelog: added support for the CuBox TDA995x
+ credits: warped-rudi
+ * lower retry timeout for source switches
+ * cec-client: wait for the source switch to finish when cec-client is
+ called with the -s switch
+ * request the power status of the TV directly after registering a new
+ client
+ * fixed:
+ * don't keep trying to send 'image view on' commands to the TV when no TV
+ is connected, and just send the 'set active source' command. fixes source
+ switch and debug log spam for people without a TV connected
+ * don't keep waiting for an updated power status from the TV for Panasonic,
+ but request a status update once every 5 seconds, or we can possibly wait
+ forever for the tv to send it
+ * log what we received exactly when logging FIXME
+ * typo in CVLCommandHandler::VendorPreActivateSourceHook. bugzid: 1087
+ * if we failed to get the physical address of the device that we are
+ connected to in the config, then try to use the address that was
+ persisted in the eeprom before resetting to the default value, 1.0.0.0.
+ closes #50.
+ * don't update the device status of unregistered/broadcast
+ * log all device status changes
+ * CCECClient::IsLibCECActiveSource returns false now while the active
+ source command is pending
+ * log failed acks and other errors in the debug log again
+ * don't send 'image view on' when the TV is already powering up
+ * reset the delayed source switch timeout properly, so we don't spam
+ commands every second
+ * don't change the device status when sending a delayed source switch
+ * don't send out commands to a device that is marked as not present or
+ handled by libCEC
+
+ -- Pulse-Eight Packaging <packaging@pulse-eight.com> Thu, 11 Oct 2012 15:48:00 +0100
+
libcec (2.0.1-1) unstable; urgency=low
* changed/added:
* added Loewe support
* added signal handlers to client applications
* Documentation updated
+ * replaced cec-config-gui by libCEC tray
* log the exact data for failed transmissions, not the opcode
+ * don't log every frame, unless debugging was enabled in ./configure or
+ visual studio
+ * changed some log levels from NOTICE to DEBUG, so the non-debugging output
+ is less spammy
* interface changes:
* WARNING: breaking API changes
* clean up: deprecated methods and fields removed
* callback parameters changed to fix plain C compilation
+ * added GetAdapterProductId()+GetAdapterVendorId()/
+ cec_get_adapter_product_id()+cec_get_adapter_vendor_id()
+ * added iDoubleTapTimeoutMs to libcec_configuration
+ * remove all pre-v2.0 compatibility checks
* fixed:
* fix plain C compilation
* prevent sending directly addressed commands from being sent to broadcast
* don't wait for a response when sending a reply, so we don't block message
handling
-
- -- Pulse-Eight Packaging <packaging@pulse-eight.com> Wed, 3 Oct 2012 16:49:00 +0100
+ * message response signaling and logging
+ * prevent double taps by not sending the same key press twice within 200ms
+ * fall back to the primary client when
+ CCECProcessor::HandleLogicalAddressLost() and no client could be found
+ * no more delay up to 2 seconds when exiting libCEC
+ * don't get caught in a loop in CVLCommandHandler when the source switch
+ was not allowed and no power status request was sent
+ * always send image view on to the tv, don't check the power status
+ * only respond to vendor commands for panasonic if we are the destination
+ * rpi: current firmware first sends a change to logical address 'broadcast'
+ and then signals us that the address was lost. libCEC then failed to
+ re-register, because it didn't know any client at this address
+
+ -- Pulse-Eight Packaging <packaging@pulse-eight.com> Mon, 8 Oct 2012 21:30:00 +0100
libcec (1.9.1-1) unstable; urgency=low